Maple-systems HMI5000 Series Manuel d'utilisateur Page 13
- Page / 202
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
HMI Local Setup 7
1010-1007, Rev. 10
Chapter 2 – HMI Local Setup
Factory Configuration
Each HMI arrives from the factory with a demo project file that illustrates some of the most popular features of the
HMI. For a first time user, it is worthwhile to navigate through the screens in the demo project and become familiar
with the features and capabilities of the HMI and EZware-5000. Refer to the EasyBuilder-5000 Help file for more
information about the features and operation of the HMI and EasyBuilder-5000.
The HMI also has a black reset push button and a four position DIP switch located through an access hole on the back
of the enclosure. The reset switch can be used to reinitialize the HMI if the HMI malfunctions. DIP switch 1 puts the
HMI into Touch Calibration mode. For normal operation, all of the DIP switches should be set to the OFF position.
This chapter describes how to use the HMI5000 Series’ local setup options. The local setup allows touchscreen
calibration, transferring projects to and from the HMI, configuring the HMI’s IP settings, passwords, time and date,
screen contrast, as well as managing the storage of recipe and history files. Additionally, memory and other system
information can be viewed.
Calibrating the Touchscreen
The touchscreen of the HMI is fully calibrated before it leaves the factory so there is no need to adjust it. However,
over time the touchscreen may need to be recalibrated.
To calibrate the touchscreen:
1. Turn DIP switch 1 ON.
2. Cycle power to the HMI (or press the reset button next to the DIP switches).
3. After the HMI displays a crosshair cursor, you are prompted to touch the cursor for:
Top left position Top right position
Center position
Bottom left position Bottom right position
4. You have the option to restore the system settings password to the default setting (111111). If you choose
Yes, a dialog box will inform you that the project will be erased in the HMI. You must type Yes to complete the
operation. After performing this operation, you must reset the Upload, Download, and Upload (History)
Passwords in the System Settings Security tab. When you next download a project, check the Firmware and
Font files checkboxes in the Download dialog.
If you choose No or allow the option to timeout, the HMI will resume initializing and run the project.
Screen calibration is accessed through the System Setup Toolbar on the HMI5104XH, HMI5121X, and HMI5150X
(see below).
Getting into Local Setup
Accessing the local setup menus requires a USB-mouse connected to the HMI (except the HMI5043N/T and
HMI5056N). Using the mouse, point to the lower right-hand corner of the HMI. The open bar icon will appear. Click on
the icon to call up the System Setup Toolbar (note this toolbar is on the HMI screen):
Open/close bar icon
Virtual keyboard icon
System info icon
Small keyboard icon
Large keyboard icon
System settings icon
Older Models
Newer Models
- 1010-1007, Rev. 10 1
- COPYRIGHT NOTICE 2
- WARRANTY 2
- IF SERVICE IS REQUIRED 2
- APPLICATIONS ASSISTANCE 2
- Table of Contents 3
- Chapter 1 – Introduction 7
- What You Need 8
- OIT/HMI Basics 9
- What is an HMI5000 Series? 10
- List of Features 11
- Chapter 2 – HMI Local Setup 13
- Changing the System Settings 14
- Viewing System Information 19
- 1010-1007, Rev. 10 24
- HMI5000 Series 31
- Touchscreen 31
- Troubleshooting 32
- Starting EasyBuilder-5000 33
- Creating a Bargraph 33
- To create Window 11: 33
- To create a Function Key: 35
- To create a Bargraph: 38
- To create a Set Word: 41
- To create a Bit Lamp: 45
- To create a Set Bit: 48
- Finishing Up 50
- Saving your first project 50
- Compiling your first project 51
- Chapter 5 – Simulator Mode 55
- To use EasySimulator 57
- Overview 58
- The Project Manager 58
- HMI IP, Password Settings 59
- Reboot HMI 59
- Connection Setting 59
- Editor Settings 59
- Easy Converter 107
- EasyPrinter 112
- Transfer Settings 118
- Simulation Settings 118
- Pass-through mode 119
- Chapter 7 – Creating Windows 122
- Creating a New Window 123
- Window Settings 125
- Assigning Size of Window 126
- Assigning a Position 126
- Monopoly Feature 126
- Assigning Underlay Windows 127
- Creating a Frame 128
- Window Background 128
- Deleting a Window 129
- Using Base Windows 129
- Using the PLC 130
- Using the Common Window 135
- System Message Windows 143
- Using the Tag Library 147
- Creating the Label Library 148
- Using the Label Library 151
- How to Create a Keypad 153
- Creating Bar Graphs 158
- Creating Meter Displays 160
- History Data Display 169
- Using Alarms 174
- Using Events 180
- Chapter 12 – Security 183
- Object Security 185
- Safety Control 186
- Interlock 186
- Auto logout 188
- Additional Security Features 189
- Disable Upload Function 190
- XOB Password 191
- Decompiling Prohibited 192
- System Passwords 193
- Security 191 197
Produits connexes et manuels pour Accessoires pour ordinateurs Maple-systems HMI5000 Series
(264 pages)© 2020, manymanuals.fr. Tous droits réservés | 2.873 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels