Maple-systems HMI5000 Series Manuel d'utilisateur Page 71
- Page / 202
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Using EZware-5000 65
1010-1007, Rev. 10
Trigger address + 1
Number of words to transfer
(32 words maximum)
The number of words to transfer from the
PLC to the HMI or HMI to PLC.
Trigger address + 2
PLC Data Address Offset
The Address Offset (from the Trigger
address + 4) at which the transfer of data
to/from the PLC will start.
Trigger address + 3
HMI Data Address Offset
The Address Offset at which the transfer of
data to/from the HMI will start.
Note: The HMI will transfer data to/from the Device Type specified by the Trigger address.
It is recommended that the data in (Trigger Addr + 1), (Trigger Addr +2), and (Trigger Addr +3) be set before writing
the Operation Code to (Trigger Addr).
Backlight Control (Write Back)
Allows the PLC to control the HMI’s backlight via the bit specified in the Trigger address. Once the requested
operation has been performed, the HMI will reset the bit.
Note: The PLC Control Object may be configured with two Backlight Control (Write Back) items, with different bits for
the On and Off control. The backlight can then be controlled directly from the PLC.
Backlight Control
Operates the same as the Backlight Control (Write back) attribute described above, but the HMI will not reset the bit
specified in the Trigger address.
Sound Control
Plays the selected sound when the bit specified by the Trigger address matches the trigger mode conditions.
Execute Macro Program
Executes the designated macro when triggered by the bit specified in the Trigger address.
Note: Only available when a macro has been created in the project.
Screen Hardcopy
Prints the specified window when the bit specified by the Trigger address matches the trigger mode conditions. The
Source window for print option provides the following selections:
Current base window: When the trigger occurs, the window currently displayed on the HMI is printed.
Window no. from register: When the trigger occurs, the window number is read from the specified register; the
window is displayed and printed.
Designate window no.: The window is selected from a list during project development. When the trigger occurs, this
pre-selected window is displayed and printed.
The Printer field allows you to select the destination for the screen hardcopy: a printer attached to the HMI, one of
the USB ports, or the Remote Printer Server.
Data Transfer (Time-based)
The Data Transfer (Time-based) Object is used to transfer bit-based or word-based data from the specified Source
address(es) to the specified Destination address(es) at periodic intervals. The interval is adjustable from 0.5 to 25.5
seconds, in 0.1 second steps.
The Address type selects whether the data transferred is word or bit, and the No. of word/No. of bit field specifies
how many consecutive addresses are transferred. The Source and Destination address fields define the starting
addresses.
- 1010-1007, Rev. 10 1
- COPYRIGHT NOTICE 2
- WARRANTY 2
- IF SERVICE IS REQUIRED 2
- APPLICATIONS ASSISTANCE 2
- Table of Contents 3
- Chapter 1 – Introduction 7
- What You Need 8
- OIT/HMI Basics 9
- What is an HMI5000 Series? 10
- List of Features 11
- Chapter 2 – HMI Local Setup 13
- Changing the System Settings 14
- Viewing System Information 19
- 1010-1007, Rev. 10 24
- HMI5000 Series 31
- Touchscreen 31
- Troubleshooting 32
- Starting EasyBuilder-5000 33
- Creating a Bargraph 33
- To create Window 11: 33
- To create a Function Key: 35
- To create a Bargraph: 38
- To create a Set Word: 41
- To create a Bit Lamp: 45
- To create a Set Bit: 48
- Finishing Up 50
- Saving your first project 50
- Compiling your first project 51
- Chapter 5 – Simulator Mode 55
- To use EasySimulator 57
- Overview 58
- The Project Manager 58
- HMI IP, Password Settings 59
- Reboot HMI 59
- Connection Setting 59
- Editor Settings 59
- Easy Converter 107
- EasyPrinter 112
- Transfer Settings 118
- Simulation Settings 118
- Pass-through mode 119
- Chapter 7 – Creating Windows 122
- Creating a New Window 123
- Window Settings 125
- Assigning Size of Window 126
- Assigning a Position 126
- Monopoly Feature 126
- Assigning Underlay Windows 127
- Creating a Frame 128
- Window Background 128
- Deleting a Window 129
- Using Base Windows 129
- Using the PLC 130
- Using the Common Window 135
- System Message Windows 143
- Using the Tag Library 147
- Creating the Label Library 148
- Using the Label Library 151
- How to Create a Keypad 153
- Creating Bar Graphs 158
- Creating Meter Displays 160
- History Data Display 169
- Using Alarms 174
- Using Events 180
- Chapter 12 – Security 183
- Object Security 185
- Safety Control 186
- Interlock 186
- Auto logout 188
- Additional Security Features 189
- Disable Upload Function 190
- XOB Password 191
- Decompiling Prohibited 192
- System Passwords 193
- Security 191 197
Produits connexes et manuels pour Accessoires pour ordinateurs Maple-systems HMI5000 Series
(264 pages)© 2020, manymanuals.fr. Tous droits réservés | 1.493 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels